Navy Body Fat Calculator

cm
cm
cm
cm
Health Updated 14 Jun 2026

Navy Body Fat Calculator is a health and wellness calculator that helps you calculate navy body fat values from your input data. The formula used is: Men: 495 / (1.0324 − 0.19077·log10(waist−neck) + 0.15456·log10(height)) − 450. Enter values using the units shown next to each input field (e.g. kg, cm, years).

  • Estimate only; not a substitute for DXA or hydrostatic weighing.

Formula

Men: 495 / (1.0324 − 0.19077·log10(waist−neck) + 0.15456·log10(height)) − 450
  • Navy Body Fat Calculator gives you a fast estimate using your inputs and updates instantly when you change any value.
  • Formula: Men: 495 / (1.0324 − 0.19077·log10(waist−neck) + 0.15456·log10(height)) − 450
  • Input definitions: • Height: the numeric height used in the calculation • Neck: the numeric neck used in the calculation • Waist: the numeric waist used in the calculation • Hip (women): the numeric hip (women) used in the calculation
  • Manual method: write down each input, apply the formula step by step, then compare your manual result with the calculator output.
  • Enter values using the units shown next to each input field (e.g. kg, cm, years).
  • This calculator uses widely accepted health formulas and returns screening estimates only. It does not replace a diagnosis from a qualified healthcare professional.
  • Compare your result with published reference ranges. Values outside the normal range warrant a conversation with your doctor.
  • Practical tip: test a low, medium, and high scenario to understand sensitivity before making decisions.

Example Calculation

Inputs
  • Height: 175 cm
  • Neck: 38 cm
  • Waist: 85 cm
  • Hip (women): 95 cm

Suppose you enter: Height = 175, Neck = 38, Waist = 85, Hip (women) = 95. The calculator applies the formula (Men: 495 / (1.0324 − 0.19077·log10(waist−neck) + 0.15456·log10(height)) − 450) and shows all output values below. Change any input field to immediately see how the result changes.

Frequently asked questions

What is the Navy Body Fat?
The Navy Body Fat Calculator is a health and wellness calculator that helps you calculate navy body fat values from your input data. Enter values using the units shown next to each input field (e.g. kg, cm, years).
When should I use this calculator?
Use this calculator whenever you need a quick, accurate result for navy body fat values from your input data without working through the arithmetic manually.
What units should I enter?
Enter values using the units shown next to each input field (e.g. kg, cm, years).
How accurate are the results?
This calculator uses widely accepted health formulas and returns screening estimates only. It does not replace a diagnosis from a qualified healthcare professional.
How do I interpret the result?
Compare your result with published reference ranges. Values outside the normal range warrant a conversation with your doctor.
How can I verify the calculation manually?
Use the displayed formula and work through the numbers step by step. If your manual result differs slightly, check rounding and unit conversions first.
Can I use this for planning and budgeting?
Yes. Run best-case, expected, and worst-case inputs to compare outcomes and make safer planning decisions.

Related calculators

Army Body Fat Calculator Estimate your body-fat percentage with the US Army tape-test method and check it against the Army's maximum allowable standard for your age and gender. It uses the same circumference equations as the Navy method — based on height, neck and waist (plus hip for women) — then compares the result to the Army body-fat limits. Enter your measurements in centimetres to see your estimated body fat and whether it is within standard. Body Fat Calculator Popular Estimate your body fat percentage with the US Navy circumference method. Enter your sex, height, and a few tape measurements to see your body fat percentage, category, and healthy range. FFMI Calculator FFMI Calculator is a health and wellness calculator that helps you calculate ffmi values from your input data. The formula used is: Lean Mass (kg) = Weight × (1 − Body Fat %/100)\nFFMI (raw) = Lean Mass / height(m)²\nFFMI (normalised) = FFMI_raw + 6.1 × (1.8 − height_m). Enter values using the units shown next to each input field (e.g. kg, cm, years).